Promise Technology SUPERSWAP 1600 Instrukcja Użytkownika

SUPERSWAP 1600USER MANUALVersion 1.0a

SuperSwap 1600 User Manual4Check the Fit of Your SATA Disk DrivesSome of the early 3.5-inch, 1.5 Gb/s SATA disk drives may not be compatible with Supe

5Chapter 2: Installation• Unpack your SuperSwap 1600 (below)• Install the Enclosure (page 6)• Install a Disk Drive (page 11)• Remove a Disk Drive (pag

SuperSwap 1600 User Manual6Install the EnclosureTo install the enclosure in your computer chassis, follow these steps:1. Power down your computer and

Chapter 2: Installation77. Install and snug the four screws into the four threaded mounting holes (two on each side) of the housing assembly. NoteIf

SuperSwap 1600 User Manual88. Connect a SATA or SAS data cable from your SATA or SAS Controller card to the data connector on the SuperSwap enclosure.

Chapter 2: Installation910. Optional. If you are installing multiple SuperSwap 1600s, install a 6-pin daisy-chain cable from the daisy-chain OUT conne

SuperSwap 1600 User Manual1012. Set the Sequential Startup switch to ON. See “Sequential Startup Option,” below.13. Replace the computer’s cover and r

Chapter 2: Installation11Install a Disk Drive3.5-inch Drive1. Press the release button and slide the cover off the drive carrier.CautionIn all other c

SuperSwap 1600 User Manual122. Carefully place a SATA or SAS disk drive into the drive carrier and slide it all the way to the back.3. Install and ti

Chapter 2: Installation132.5-inch DriveFor 2.5-inch disk drives, Promise provides an installation kit, sold separately as a spare part, consisting of

SuperSwap 1600 User ManualiiCopyright© 2006 Promise Technology, Inc. All Rights Reserved.Copyright by Promise Technology, Inc. (Promise Technology). N

SuperSwap 1600 User Manual142. Attach the bracket to the side of the disk drive, using the short round-head screws (that came with the kit). Be sure y

Chapter 2: Installation154. Install two long round-head screws (that came with the SuperSwap) through the holes in the side of the drive carrier to at

SuperSwap 1600 User Manual166. Carefully turn the drive carrier over and tighten the screws attaching the bracket.7. Slide the cover onto the drive ca

Chapter 2: Installation174. Insert the key and turn it 90 degrees clockwise to lock the drive carrier in the enclosure. Remove a Disk Drive1. Pull th

SuperSwap 1600 User Manual18View SuperSwap in WebPAMYou can combine SuperSwap 1600 with a Promise FastTrak RAID Controller and WebPAM RAID management

19Chapter 3: Troubleshooting•LEDs (below)• Interpret LED Displays (page 20) • Disk Drive Replacement (page 22)• Fan Replacement (page 23)• Contact Tec

SsuperSwap 1600 User Manual20Troubleshooting is based on observing and analyzing LED colors. There are two LEDs on SuperSwap 1600: • Status – Report

Chapter 3: Troubleshooting21Fix: If the Status LED continues to display amber, remove the disk drive for testing. Return the drive to service or repla

SsuperSwap 1600 User Manual22Event: WebPAM reports fan speed out of specification. Cause: The fan is turning too slowly, WebPAM reports the condition.

Chapter 3: Troubleshooting23Fan ReplacementTo replace a fan on the SuperSwap 1600:1. Power down the PC.2. Remove the SuperSwap enclosure from the PC c

NoticesiiiRadio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, purs

SsuperSwap 1600 User Manual248. Plug in the power connector of the new fan.9. Carefully place the circuit board and fan back into the enclosure.Check

Chapter 3: Troubleshooting25Contact Technical SupportPromise Technical Support provides several support options for Promise users to access informatio

SsuperSwap 1600 User Manual26GermanyItalyTaiwan E-mail Support [email protected] Technical Support +49 (0) 2 31 56 76 48 - 29Attn: Techni

Chapter 3: Troubleshooting27China Limited WarrantyPromise Technology, Inc. (“Promise”) warrants that for three (3) years from the time of the delivery

SsuperSwap 1600 User Manual28Disclaimer of other warrantiesThis warranty covers only parts and labor, and excludes coverage on software items as expre

Chapter 3: Troubleshooting29Your ResponsibilitiesYou are responsible for determining whether the product is appropriate for your use and will interfac

SsuperSwap 1600 User Manual30You must follow the packaging guidelines for returning products:• Use the original shipping carton and packaging• Include

SuperSwap 1600 User Manualiv

vContentsChapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1About This Manual . . . . . . . . . . . .

SuperSwap 1600 User Manualvi

1Chapter 1: Introduction• About This Manual, below• Overview (page 2)• Specifications (page 3)• Key Features (page 3)• Check the Fit of Your SATA Disk

SuperSwap 1600 User Manual2OverviewThe SuperSwap 1600 drive enclosure installs easily into a 5.25-inch component bay in your personal computer or work

Chapter 1: Introduction3Specifications• Fits most 3.5-inch and 2.5-inch form factor SATA and SAS disk drives• Occupies one 5.25-inch component bay in